Updated Nov 16, 2026· 8 min read

Key takeaways

  • Skipping the outlet test and replacing parts when the wall socket was the issue.
  • Forgetting the PSU rear switch after moving the case or working inside it.
  • Plugging an 8-pin CPU power lead into the wrong header, or leaving it out entirely.
  • Working inside the case while it is still plugged in.
  • Opening the power supply to look inside. This is dangerous and can void the warranty.
  • Replacing the motherboard first. Boards are more expensive to swap than a cord, switch, or PSU, so rule out the cheap suspects first.
  • Using an underpowered PSU for a high-draw graphics card, then wondering why the machine shuts down at start-up.

If a PC shows no lights and no fans at all, the usual culprits are the wall outlet or power strip, the power supply switch, a loose motherboard power cable, or the front-panel power button lead, and checking them in that order resolves most cases without spending anything. Work from the outside in: confirm the outlet, then the cord, then the supply, then the connections inside the case.

Quick Answer: The Fastest Checks First

Before opening anything, confirm that the outlet works by plugging in a lamp or phone charger. Move the PC cable out of any power strip and into the wall directly, because strips and surge protectors can fail or trip. Make sure the rocker switch on the back of the power supply is set to the on position (the I side, not the O side), and reseat the power cord at both ends. Try a different cord if you have one; a cord is cheap and fails more often than people expect.

If those steps change nothing, shut the PC down fully, unplug it, and hold the power button for several seconds to discharge residual power. Then continue with the internal checks below. Always unplug the machine before touching anything inside, and never open the power supply itself. The inside of a PSU can hold dangerous charge even when unplugged.

First Decide What “No Power” Actually Means

The word “no power” covers several different symptoms, and each points to a different cause. Sorting yours into the right row saves a lot of guessing.

Symptom Likely cause First thing to try
No lights, no fans, nothing on the motherboard Outlet, cord, PSU switch, failed PSU Different outlet and cord, check rear switch
Small standby LED on the motherboard is lit, but pressing power does nothing Front-panel power switch lead, case button, or power-on signal issue Reseat the front-panel header pins, or briefly short the power switch pins as the motherboard manual describes
Fans twitch for a second, then everything stops Short circuit, bad connector, protection circuit in the PSU tripping Strip the system to minimum parts and rebuild
Fans and lights run, but no display Not a no-power fault; RAM, GPU, or CPU seating Reseat RAM and GPU, try a different video port
Powers on, then shuts off after seconds Overheating, CPU cooler not mounted, PSU protection Confirm the cooler is attached and fans spin

If your fans spin and the lights come on but the screen stays black, that is a no-display problem rather than a no-power one, and the troubleshooting is different. This guide focuses on the case where nothing responds.

Step-by-Step Checks

1. Power source and cable

Test the outlet with another device. Remove extension cords, power strips, and any uninterruptible power supply from the chain for the test. A UPS with a depleted or faulty battery can refuse to pass power, and surge strips have internal protection that can trip and cut output. Plug the PC straight into a known-good wall outlet using a known-good cable.

2. The PSU switch and the standby LED

Flip the PSU switch off, wait a few seconds, and flip it on. Many modern motherboards have a tiny standby LED that lights when the PSU delivers standby power. Where the maker’s manual documents it, this LED tells you the board is getting its always-on supply. If the LED is lit, your power chain is at least partly alive and the problem is likely downstream, such as the power button circuit. If the LED stays dark, suspect the PSU, the cord, the outlet, or the main motherboard power cable.

3. Main motherboard power connectors

Open the case with the PC unplugged. Locate the large 24-pin ATX connector and the 4-pin or 8-pin CPU power connector near the top-left of the motherboard. These connectors must click into place; a half-seated 24-pin connector is a classic cause of a board that appears dead. Press each firmly until the latch engages. Also confirm the 8-pin CPU cable is plugged into the CPU socket header and not into a PCIe graphics header, because they look similar but are not interchangeable.

4. Front-panel power button wiring

The case’s power button connects to a small header, often labeled PWR_SW or PWR, in a cluster of front-panel pins. If the header was disturbed during a build or cleaning, the board never receives the power signal. The motherboard manual has a diagram showing which two pins are the power switch. Reseat that connector. Many manuals also describe briefly touching the two pins together with an insulated tool to simulate the button; follow the manual, and do this only with the PC fully assembled and the PSU switch on, with care. If the machine starts this way, the case button or its lead is faulty.

5. Strip down to the minimum

Remove everything non-essential: extra drives, add-in cards, USB devices, extra RAM sticks, and case front I/O connectors. A faulty peripheral, a stray screw, or a standoff touching the back of the board can cause a short that makes the PSU shut down instantly. Check that the number of motherboard standoffs matches the mounting holes, and that none sit under a spot where no hole exists. Rebuild piece by piece, testing after each addition.

6. Test with another power supply

If everything else looks right, the power supply is the next suspect. Borrowing a known-good PSU of adequate wattage is the cleanest test. A PSU paper-clip test is sometimes described online, but it only shows whether the fan spins under no load and does not prove the unit delivers correct voltages, so treat it as a rough indicator at best. A dedicated PSU tester or a multimeter reading is more informative, but if you are not comfortable with that, ask a technician. Do not open the PSU casing.

Common Causes at a Glance

Cause How it shows up Fix
Dead outlet or tripped strip Totally dark, even the standby LED Use a different outlet, bypass the strip
PSU rear switch off or loose cord No standby LED Switch on, reseat the cord, try another cord
Half-seated 24-pin or CPU cable Standby LED lit, no response Reseat firmly until the latch clicks
Front-panel lead disturbed Standby LED lit, button does nothing Reseat PWR_SW pins per manual
Short from a standoff or part Brief spin then shutoff, or nothing Check standoffs, strip to minimum
Failed power supply No response with good cords and connections Swap in a known-good PSU, replace under warranty
Failed motherboard Good PSU yet no standby behavior Contact the maker or a repair technician

If It Used to Work

When a previously healthy PC suddenly goes dead, think about what changed. A storm or power flicker may have damaged the PSU or tripped a protective device. A new component may have drawn more power than the old supply could deliver, or a cable may have been knocked loose while cleaning dust. Dust buildup itself can cause overheating shutdowns. Cleaning with the PC off and unplugged, using compressed air in short bursts while holding fans still, can help, but be gentle with fan blades.

For a build that never worked, review the basics: both CPU power and the 24-pin connector present, RAM seated until both clips snap, CPU cooler mounted with its fan header connected, and the case standoffs correct. A new build that shows life for a moment then stops is often a CPU power cable omission or a short.

Common Mistakes

  • Skipping the outlet test and replacing parts when the wall socket was the issue.
  • Forgetting the PSU rear switch after moving the case or working inside it.
  • Plugging an 8-pin CPU power lead into the wrong header, or leaving it out entirely.
  • Working inside the case while it is still plugged in.
  • Opening the power supply to look inside. This is dangerous and can void the warranty.
  • Replacing the motherboard first. Boards are more expensive to swap than a cord, switch, or PSU, so rule out the cheap suspects first.
  • Using an underpowered PSU for a high-draw graphics card, then wondering why the machine shuts down at start-up.

When to Stop and Call for Help

If you smell burning, see scorch marks, or notice a bulging or leaking component, stop and unplug the PC. If the machine remains dead after swapping in a known-good PSU, cord, and outlet, the motherboard or CPU may be at fault, and a technician or the maker’s support can diagnose it further. If the PC is within warranty, contacting the maker before disassembling extensively is wise, since support teams often have a defined troubleshooting sequence. For a graphics card with a 12VHPWR or 12V-2×6 cable, follow the GPU and PSU maker guidance on seating the connector fully, and stop using the card if you see heat damage on the plug.

Frequently Asked Questions

Why does my PC have no power but the motherboard LED is on?

A lit standby LED usually means the power supply is feeding the board’s always-on rail. The fault then often lies in the power button, its header wiring, or a connector that is not fully seated. Reseat the front-panel header and the main power cables, and consult the board manual.

Can a bad power supply cause a PC not to turn on at all?

Yes. A failed or protection-tripped power supply is one of the most common reasons for a completely dead PC. Testing with a known-good unit of similar capacity is the clearest way to confirm it.

Could a power strip or surge protector be the problem?

It can. Surge strips contain protection components that wear out or trip, and a faulty strip may supply no output. Plug the PC directly into a wall outlet to rule this out.

Is it safe to try the paper-clip test on a PSU?

The test is widely described, but it only shows whether the PSU turns on without a load and says little about voltage quality. If you try it, unplug everything from the PSU and follow the unit’s documentation. When in doubt, use a PSU tester or ask a technician.

Should I clear the CMOS if the PC will not power on?

A CMOS reset helps when a PC powers up but fails to post, not when there is no power at all. If the board shows life, the manual’s reset procedure is a reasonable step, but for a truly dead system focus on power delivery first.

How do I know if the motherboard is dead?

If a known-good PSU, cord, and outlet still produce no standby LED or response, the motherboard becomes a suspect. Confirming it usually takes a spare board or a technician, so contact the maker’s support or a repair shop at that point.

R
Ryan Sullivan
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.

FAQ

Why does my PC have no power but the motherboard LED is on?
A lit standby LED usually means the power supply is feeding the board’s always-on rail. The fault then often lies in the power button, its header wiring, or a connector that is not fully seated. Reseat the front-panel header and the main power cables, and consult the board manual.
Can a bad power supply cause a PC not to turn on at all?
Yes. A failed or protection-tripped power supply is one of the most common reasons for a completely dead PC. Testing with a known-good unit of similar capacity is the clearest way to confirm it.
Could a power strip or surge protector be the problem?
It can. Surge strips contain protection components that wear out or trip, and a faulty strip may supply no output. Plug the PC directly into a wall outlet to rule this out.
Is it safe to try the paper-clip test on a PSU?
The test is widely described, but it only shows whether the PSU turns on without a load and says little about voltage quality. If you try it, unplug everything from the PSU and follow the unit’s documentation. When in doubt, use a PSU tester or ask a technician.
Should I clear the CMOS if the PC will not power on?
A CMOS reset helps when a PC powers up but fails to post, not when there is no power at all. If the board shows life, the manual’s reset procedure is a reasonable step, but for a truly dead system focus on power delivery first.
How do I know if the motherboard is dead?
If a known-good PSU, cord, and outlet still produce no standby LED or response, the motherboard becomes a suspect. Confirming it usually takes a spare board or a technician, so contact the maker’s support or a repair shop at that point.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free
Prime for Young Adults

A Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.

See Prime for Young Adults
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free

As an Amazon Associate we earn from qualifying purchases.